CPS presents aguide to setup the communication between Micro – ROS and ROS2 and control multiple servos attached to a PWM/Servo Driver board. Therefor the installation of ROS2, the setup of a Micro – ROS workspace, the establishment of the communication with a custom message and the implementation of third party libraries as well as the usage of two different RTOS system will be described step for step.
By combining the power of Micro ROS Foxy, ESP32 and a PCA9685 board, this project provides a way of controlling multiple servos. The setup has been tested on a Linux Ubuntu 20.04.6 LTS environment, allowing seamless communication and accurate servo positioning. The linked guide give some information about Micro – ROS and walks through the installation of ROS2, the setup of a Micro-ROS workspace, and the establishment of the communication between Micro-ROS and ROS2 using a custom message format called “ServoMessage”. Additionally, the guide covers the implementation of third-party libraries and the usage of two different RTOS systems. The code includes examples of how to use the Micro ROS Foxy framework to send and receive ServoMessages over the ROS2 network to control the attached servos.
Update 17.03.2023: Added instructions for dealing with ESP32-S2 hardware.
This guide should enable you to install ROS 2 Humble on a fresh Ubuntu installation and compile micro-ROS for ESP32 using automated scripts. Additionally, I added the section for running a docker container, so the guide should work on almost any Linux based system which has docker installed.
Section Part II is added, that includes instructions for compiling micro-ROS for ESP32-S2 based devices. The problem here is, that the standard micro-ROS distribution mentioned in the official tutorial does not ship with a current espressif-idf that supports ESP32-S2 boards. It seems like you need an esp-idf above version 4.4.
We will use the FreeRTOS implementation for ESP32. Steps will lead to automatic compilation of provided “app” for the ESP32 and connect it to the ROS humble environment.
Step 1 – Only if using docker is intended
docker run -it --net=host -v /dev:/dev --privileged ros:humble
Step 2: Download micro-ROS and install dependencies
# Source the ROS 2 installation
# Create a workspace and download the micro-ROS tools
git clone -b $ROS_DISTRO https://github.com/micro-ROS/micro_ros_setup.git src/micro_ros_setup
# Update dependencies using rosdep
sudo apt update && rosdep update
rosdep install --from-paths src --ignore-src -y
# Install pip
sudo apt-get install python3-pip
# Build micro-ROS tools and source them
Step 3: Create new firmware workspace – this time for platform esp32
Pay attention to use platform “esp32”
# Create step
ros2 run micro_ros_setup create_firmware_ws.sh freertos esp32
Step 4: Configure the firmware to include the application
# Configure step with ping_pong app and serial transport
ros2 run micro_ros_setup configure_firmware.sh ping_pong --transport serial
Step 5: Build the firmware
# Build step
ros2 run micro_ros_setup build_firmware.sh
Step 6: Flash the firmware
Connect esp32 via USB cable or appropriate interface. Most likely all the esp32 dev-boards offer USB connection and will be recognized as ttyUSB0 (USB serial device). In this step, the flash program will find the right port for you automatically.
Caveat ahead: If you are not running the process as root user (which is the recommended approach anyways), you must make sure that you have write permissions on the /dev/ttyUSB0 device. That can be established like follows:
sudo chown $USER /dev/ttyUSB0
Depending on your configuration, it is possible that you need to adapt above command. By running the flash step you will most likely see which device you need to use when the process exits with an error 🙂
# Flash step
ros2 run micro_ros_setup flash_firmware.sh
Step 7: Connect to the device and test the firmware
To make sure everything is working, disconnect the device after the flashing process is done or just reset it via the enable button (EN).
# Download micro-ROS-Agent packages
ros2 run micro_ros_setup create_agent_ws.sh
# Build step
ros2 run micro_ros_setup build_agent.sh
# Run a micro-ROS agent
ros2 run micro_ros_agent micro_ros_agent serial --dev [device]
Replace [device] with your serial connection. Again, remember to choose the /dev/ttyUSB* device selected in the flash step. To avoid searching for the correct serial port in the future, you can also find out the discrete device identifier by having a look at this command’s output:
Step 8: Testing the micro-ROS app
At this point, the micro-ROS app is built and flashed and the board is connected to a micro-ROS agent. We now want to check that everything is working.
Open a new command line. We are going to listen to the ping topic with ROS 2 to check whether the micro-ROS Ping Pong node is correctly publishing the expected pings:
Also, we expect that, because of having received the fake_ping, the micro-ROS pong publisher will answer with a pong. As a consequence, in the pong subscriber console, we should see the board’s answer to our fake_ping:
In this case, I would advise anybody to use a docker container for the build process, as there is a bunch of dependencies installed in the process that might interfere with your currently running setup.
Make a new project directory and cd into it.
Run a docker container that already includes needed dependencies, for instance a current version of esp-idf.
Select an example project and configure it for esp32-s2. As you can see, it should also be possible to configure the firmware for esp32-s3 and -c3 models. But I have not tested that yet.
# Set target board [esp32|esp32s2|esp32s3|esp32c3]
idf.py set-target esp32s2
Use menuconfig to insert the WiFi Credentials and specific settings.
# Set your micro-ROS configuration and WiFi credentials under micro-ROS Settings
Build your micro-ROS application and flash it to your esp32-s2 device. Additionally, start a monitoring process via serial console to see if there are any errors with the device. You will probably see some errors after connecting to the network, as the corresponding micro-ROS agent is not running on the computer yet.
Start a micro-ROS agent container to connect to your newly set-up esp node.
In the end, this gives you the tools needed to compile the firmware for a ESP32-S2 based device. After exiting the build-container, the generated files are still available under provided project directory on your computer.